Can phantom power pass through a patchbay?

David Mellor

David Mellor is CEO and Course Director of Audio Masterclass. David has designed courses in audio education and training since 1986 and is the publisher and principal writer of

Tuesday November 15, 2005

You could connect your mic lines directly to your mixing console. Or you could connect them through a patchbay so you can easily rearrange the channels if necessary. But will it work?

A question from a Audio Masterclass visitor...

I have an issue I need to resolve.

It concerns connecting my 12 channel XLRf to XLRm snake, coming from the recording booth, to a Behringer PX2000 unbalanced patchbay.

Considering that I have my mic preamps also connected a patchbay, I'm wondering how would it be possible to send phantom power thru the patchbay to the mic in the booth.

Can phantom power travel through TRS-XLR cables/connectors?

P.S. The patchbay is unbalanced 1/4" jacks.

David Mellor responds...

Unfortunately, the simple answer is no. It is not possible to send phantom power through an unbalanced patchbay. Well it might be, but you would be putting 48 volts across the output pins of the microphone. A capacitor microphone will not work. A dynamic mic just might work, but I would have to worry about magnetic saturation of the core of the transformer, and possible damage.

Phantom power can be sent via any balanced connection. So an XLR - XLR cable passes phantom. A 3-pole jack to 3-pole jack cable will pass phantom power too. Naturally an XLR to 3-pole jack cable will also work.

A balanced patchbay can also be used to pass phantom power, but here we have an issue...

If a patchcord is used to connect the mixing console input providing the phantom power to the microphone, then all will be well and phantom power will pass. However, if your patchbay is normalized so you don't need to use a patchcord to make commonly-used connections, then you cannot always rely on the switch contacts to pass phantom power.

The switch contacts are very small in area and many people doubt their ability to pass mic-level signals anyway. Any oxidization of the contact surfaces will result in an intermittent connection, and perhaps distortion due to partial rectification of the signal.

Passing phantom power through the contacts seems to accelerate the deterioration.

These are my observations from personal experience. I haven't seen any formal study of this, but I would say that connecting a mic via a patchbay, using patchcords rather than normalized connections, seems to be OK.

Also, this would have to be a patchbay with full-size quarter inch jacks. I don't personally rate the smaller bantam jacks for any purpose.

Image: Phantom of the Opera

Like, follow, and comment on this article at Facebook, Twitter, Reddit, Instagram or the social network of your choice.

Come on the Audio Masterclass Pro Home Studio MiniCourse - 60 great hints and tips to get your home recording studio MOVING

It's FREE!

Get It Now >>

An interesting microphone setup for violinist Nigel Kennedy

Are you compressing too much? Here's how to tell...

If setting the gain correctly is so important, why don't mic preamplifiers have meters?

The Internet goes analogue!

How to choose an audio interface

Audio left-right test. Does it matter?

Electric guitar - compress before the amp, or after?

What is comb filtering? What does it sound like?

NEW: Audio crossfades come to Final Cut Pro X 10.4.9!

What is the difference between EQ and filters? *With Audio*

What difference will a preamp make to your recording?

Watch our video on linear phase filters and frequency response with the FabFilter Pro Q 2

Read our post on linear phase filters and frequency response with the Fabfilter Pro Q 2

Harmonic distortion with the Soundtoys Decapitator

What's the best height for studio monitors? Answer - Not too low!

What is the Red Book standard? Do I need to use it? Why?

Will floating point change the way we record?

Mixing: What is the 'Pedalboard Exception'?

The difference between mic level and line level

The problem with parallel compression that you didn't know you had. What it sounds like and how to fix it.

Compressing a snare drum to even out the level

What does parallel compression on vocals sound like?

How to automate tracks that have parallel compression

Why mono is better than stereo for recording vocals and dialogue